Table C -- TUBE SOCKET VOLTAGE CHART
THE VOLTAGE ARE READ BETWEEN THE SOCKET TERMINAL AND GROUND UNFER THE FOLLOWING CONDITIONS UNLESS OTHERWISE STATED
Headphones, Antenna and Ground discon-nected
Band Switch set for Band No. 1,200-500 kc.
Tuning Control set at 200 kc.
Crystal Control OUT position.
C.W. Oscillator OFF position.
Volume Control maximum
Dial Light Control maximum.
AVC-OFF-MVC Switch in MVC position.
|
|
All readings taken with 1000 ohm per volt meter.
Plate and Screen voltages read on 500 volt scale. Other Voltages read on appropriate scales.
See last paragraph in 34b(1) regarding possibilities of fictious voltages when using socket analyzer.
|
Socket Terminal or block | VT-117 1st R-F | VT-117 2nd R-F | VT-150 1st Det | VT-117 1st I-F | VT-177 2nd I-F | VT-116 3rd I-F | VT-233 2nd Det C.W Osc | VT-152 Audio |
1 | Shell 0 V. | Shell 0 V. | Shell 0 V | Shell 0 V | Shell 0 V | Shell 0 V | Shell 0 V | 0 V. |
2 | Heater 16,18.9 | Heater 12.6 V | Heater 0 V | Heater 25.2 V | Heater 12.6 V | Heater 6.3 V | Grid 6V Note D | Heater 25.3 V |
3 | Sup. 0 V | Sup. 3.8 V | Plate 210 V. 2 Ma | Sup 5.8 V | Sup 5.8 V | Sup16.5 V | Cathode 16.5 V.. | Plate 200 V. 18 Ma |
4 | Grid 0 V. | Grid 0 V. | Screen 100 V. Note C 6.2 Ma | Grid 0 V. | Grid 0 V. | Grid 14 V | Diode 2 V | Screen 210 V 3.4 Ma |
5 | Cathode 3.8 V. | Cathode 3.8 V. | Osc. Grid -4 V. | Cathode 5.8 V. | Cathode 5.8 V. | Cathode 16.5 V. | Diode 0 V | Grid -8 V. Note E |
6 | Screen 100 V. 2 Ma | Screen 85 V. 1.6 Ma | Cathode 0 V. | Screen 105 V. 1.6 Ma. | Screen 105 V. 1.6 Ma. | Screen 100 V. .85 Ma | Plate 55 V. Note B (CW Osc On) .95 Ma. | Tie Terminal ,2 V. |
7 | Heater 12.6 V,. | Heater 6.3 V. | Heater 6.3 V. | Heater 18,9 V | Heater 18,9 V | Heater 0 V. | Heater 6.3 V. | Heater 18.9 V. |
8 | Plate 100 V 9 Ma | Plate 170 V 6 Ma | Grid -1.8 V | Plate 185 V. 5.6 Ma. | Plate 210 V. 5.8 Ma. | Plate 210 V. 3.5 Ma. | Heater 12.6 V. | Cathode 0 V. |
Note A - The shell (no, 1 Terminal) of the 2nd r-f tube is not at ground potential but connected to the cathode. For that reason the flexible lead from the octal Socket Adaptor is not Inserted Into ground pin jack but is inserted into the Adaptor No. 3 outer pin jack.
Note B - 55 volts read at socket terminal 45 volts read with adaptor plug - see last paragraph of 34b(1).
Note C - 60 Volts read with analyzer. See Note D.
Note D - As read on 50 - volt scale.
Note E - As read on 500 - volt scale.
Note F - 650 volts read with analyzer. See Note B.
|